|
Model
CR
6KW- 001
Includes
6KW Heater
Circulation Pump
PVC & Related Parts for Installation
CR 11.5 KW- 001
Includes
11.5KW Heater
Circulation Pump
Contactor
Transformer
PVC & Related Parts for Installation
|

BASIC CIRCULATION WATER HEATER FOR
BAPTISTRIES
6 KW
or 11.5KW
Specifications
Original Style Basic
Circulation Water Heater
The
Original Basic water heater was
designed in the 1960's for use and
is still available today for those
who want to replace their existing
heater with this "through the wall"
style heater. The 6KW - 001 - Kit
includes the 6 KW heater with the
circulation pump and pump
installation kit. It attaches
directly to the side of your
baptistry, with water coming in at
the bottom, being heated, and pumped
out at the top. (tub must be filled
before using). The unit is
insulated, has an adjustable
thermostat (60° - 107°F). There is a
high limit switch set at 118°F. For
use with 240V single phase power. It
can be used with 208V but heating is
reduced by 25%. With 120V, heating
is reduced by 75%. This unit will
heat 90 gallons per hour for a 30°
rise. One year manufacturers
warranty. Total height 27". Uses 1"
and 1 1/2" water connections. 6 KW
is 26" tall, 25 amps @ 240V single
phase.
Have a Larger Baptistry- over 750
gallons?
Heat your Baptistry faster!
Our Basic Water Heater is also
available in a 240V - 11.5 KW size,
which heats 115 gallons per hour to
a 30° rise. This 11.5 requires a 60
amp resistive rating contactor and
24V transformer to operate.
Our
11.5 KW Kit includes an MDI 60 Amp
- 2 pole contactor which allows
the transfer of current to handle
the larger load. It also includes a
Honeywell AT140 foot mounted
transformer, which steps down the
voltage to control the switch in the
unit.
Operates on 240V Single Phase, but
can operate on 208V at a 25%
reduction in heating.
Our price includes these items: the
11.5 KW Heater, the 1/40 HP pump,
contactor, transformer, installation
kit and instructions.
Model CR-11.5KW-001 - 240V Kit
Model CR-6KW-001 - 6 KW -
$479.00
Model CR-11KW-001 - 11.5KW -
$679.00
Free Ground Shipping to 48 States.
Call for overnight or fast delivery!
GFCI Recommended -
Info
Wiring
Diagram
Instruction Booklet
CAUTION:
Be
certain heater is turned off before
draining Baptistry. Always fill
Baptistry before turning heater on.
Dry operation will burn out heating
element, and cause failure of the
pump.
All
Electrical Connections should be
made by a qualified, licenses
electrician!
Note: These are not Little Giant
Products. Due to changes at the
manufacturer, we no longer carry
Little Giant Baptistry Products.
|
DID YOU KNOW?
Center of water
inlet to center of water outlet is
23 1/8" on the 6 KW.
INSTALLATION INFO
Assemble and make
up tightly the complete heater and
parts as shown (except slip joint
nuts). Locate the most accessible
place around the Baptistry for
installation. Drill a 2-1/8"
diameter hole 4-1/2" up from the
Baptistry floor. Smooth hole and
install chrome faced inlet flush
port, by loosening at slip joint
nut. Apply clear RTV sealant under
chrome flange. Remove any outside
insulation so port rubber gasket
fits against outside of fiberglass
wall. Measure center to center
distance exactly between inlet and
outlet fittings. Locate and drill a
2-1/8" hole for top port using
method stated above.
Assemble complete heating system
onto installed ports. Important -
Block under heater or pump to
support weight - this prevents
leakage of Baptistry wall fittings.
Heaters are shipped with special
Installation Instructions regarding
wiring, etc.
Add wood or other blocks under
your Basic Circulation heater to
help support its weight and protect
baptistry wall fittings. |